Flash Hobby F722/50A STACK

(customer review )

$90.99 $45.50

Item: F722 stack controllerMCU:STM32F722RET6IMU(Gyro): ICM42688USB Port Type: Type-CWeight: 7.5gMounting Size: 30.5*30.5mmDimension: 37(L) x 37(W) x 6.6(H)mm FLASH HOBBY BLS 60A 30.5x30.5 4-in-1 ESC Firmware: BLS 16.7Weight: 12gDimension:42.3(L) * 37(W) * 6.2mm(H)Mounting Size:30.5 x 30.5mm( 4mm hole diameter)ESC Protocol: DSHOT300/600Model:F722

Specifications
Product Name	FLASH HOBBY FS722 30.5x30.5 Flight Controller
MCU	STM32F722RET6
IMU(Gyro)	MPU6000
USB Port Type	Type-C
Barometer	BMP280
OSD Chip	BetaFlight OSD w/ AT7456E chip
DJI Air Unit Connection Way	Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Plug	Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Black box	16M Black Box
Current Sensor Input	Supported. For 50A ESC, please set scale = 180 and Offset = 0.
Power Input	3S - 6S Lipo(Through ESC 8-PIN connector)
5V BEC Output	5 grous 5V outputthe total current load is 3A
9V Output	3 groups 9V outputthe total current load is 2.5A
3.3V Output	1 group 3.3V outputmaxmum current is 300mA
ESC Signal	M1 - M4
UART	6 sets(UART2 UART5, UART3), UART6(Dedicated for SBUS), UART4(Dedicated for ESC telemetry),UART1 (Dedicated for VTX data setting)
Sbs	Debugging to UART6 Channel
ESC Telemetry	UART R4(UART4)
I2C	Supported. SDA & SCL pads on front side. Used for magnetometer.
LED Pad	Supported. LED,5V, and GND pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer	supported5V,BZ pads for 5V Buzzer
BOOT Button	Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
Supported Flight Controller Firmware	BetaFlight(Default),
Firmware Target Name	STM32F722RET6
Mounting	30.5 x 30.5mm( 4mm hole diameter)
Dimension	37(L) x 37(W) x 6.6(H)mm
Weight	7.5g
Product Name	FLASH HOBBY BLS 50A 30.5x30.5 4-in-1 ESC
Firmware	BLS 16.7
PC Configurator Download Link	https://esc-configurator.com/
Continuous Current	50A * 4
Burst Current	60A(5seconds)
TVS Protective diode	Yes
External Capacitor	35V560uF Low ESR Capacitor(In the package)
ESC Protocol	DSHOT300/600
Power Input	3-6S LiPo
Power Output	VBAT
Current Sensor	Support (Scale=180 Offset=0)
ESC Telemetry	Not supported
Mounting	30.5 x 30.5mm( 4mm hole diameter)
Dimension	42.3(L) * 37(W) * 6.2mm(H)
Weight	12g

SKU:X60794520 Category: Toys

Item: F722 stack controllerMCU:STM32F722RET6IMU(Gyro): ICM42688USB Port Type: Type-CWeight: 7.5gMounting Size: 30.5*30.5mmDimension: 37(L) x 37(W) x 6.6(H)mm FLASH HOBBY BLS 60A 30.5×30.5 4-in-1 ESC Firmware: BLS 16.7Weight: 12gDimension:42.3(L) * 37(W) * 6.2mm(H)Mounting Size:30.5 x 30.5mm( 4mm hole diameter)ESC Protocol: DSHOT300/600Model:F722

Specifications
Product Name	FLASH HOBBY FS722 30.5×30.5 Flight Controller
MCU	STM32F722RET6
IMU(Gyro)	MPU6000
USB Port Type	Type-C
Barometer	BMP280
OSD Chip	BetaFlight OSD w/ AT7456E chip
DJI Air Unit Connection Way	Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Plug	Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Black box	16M Black Box
Current Sensor Input	Supported. For 50A ESC, please set scale = 180 and Offset = 0.
Power Input	3S – 6S Lipo(Through ESC 8-PIN connector)
5V BEC Output	5 grous 5V outputthe total current load is 3A
9V Output	3 groups 9V outputthe total current load is 2.5A
3.3V Output	1 group 3.3V outputmaxmum current is 300mA
ESC Signal	M1 – M4
UART	6 sets(UART2 UART5, UART3), UART6(Dedicated for SBUS), UART4(Dedicated for ESC telemetry),UART1 (Dedicated for VTX data setting)
Sbs	Debugging to UART6 Channel
ESC Telemetry	UART R4(UART4)
I2C	Supported. SDA & SCL pads on front side. Used for magnetometer.
LED Pad	Supported. LED,5V, and GND pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer	supported5V,BZ pads for 5V Buzzer
BOOT Button	Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
Supported Flight Controller Firmware	BetaFlight(Default),
Firmware Target Name	STM32F722RET6
Mounting	30.5 x 30.5mm( 4mm hole diameter)
Dimension	37(L) x 37(W) x 6.6(H)mm
Weight	7.5g
Product Name	FLASH HOBBY BLS 50A 30.5×30.5 4-in-1 ESC
Firmware	BLS 16.7
PC Configurator Download Link	https://esc-configurator.com/
Continuous Current	50A * 4
Burst Current	60A(5seconds)
TVS Protective diode	Yes
External Capacitor	35V560uF Low ESR Capacitor(In the package)
ESC Protocol	DSHOT300/600
Power Input	3-6S LiPo
Power Output	VBAT
Current Sensor	Support (Scale=180 Offset=0)
ESC Telemetry	Not supported
Mounting	30.5 x 30.5mm( 4mm hole diameter)
Dimension	42.3(L) * 37(W) * 6.2mm(H)
Weight	12g

0 reviews for Flash Hobby F722/50A STACK

There are no reviews yet. Be the first to review this product!

Add a review

Your email address will not be published. Required fields are marked *

Cart

Your cart is empty